View MAT03AH883C_5435211.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rev. c information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. no license is granted by implication or otherwise under any patent or patent rights of analog devices. a mat03 low noise, matched dual pnp transistor features dual matched pnp transistor low offset voltage: 100 v max low noise: 1 nv/ hz @ 1 khz max high gain: 100 min high gain bandwidth: 190 mhz typ tight gain matching: 3% max excellent logarithmic conformance: r be 0.3 typ pin connection to-78 (h suffix) general description the mat03 dual monolithic pnp transistor offers excellent parametric matching and high frequency performance. low noise characteristics (1 nv/ hz max @ 1 khz), high bandwidth (190 mhz typical), and low offset voltage (100 v max), makes the mat03 an excellent choice for demanding preamplifier appli- cations. tight current gain matching (3% max mismatch) and high current gain (100 min), over a wide range of collector cur- rent, makes the mat03 an excellent choice for current mirrors. a low value of bulk resistance (typically 0.3 ? ) also makes the mat03 an ideal component for applications requiring accurate logarithmic conformance. each transistor is individually tested to data sheet specifications. device performance is guaranteed at 25 c and over the extended industrial and military temperature ranges. to ensure the long- term stability of the matching parameters, internal protection diodes across the base-emitter junction clamp any reverse base- emitter junction potential. this prevents a base-emitter breakdown condition that can result in degradation of gain and matching performance due to excessive breakdown current. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781/329-4700 www.analog.com fax: 781/326-8703 ? analog devices, inc., 2002
mat03e mat03f parameter symbol conditions min typ max min typ max unit current gain 1 h fe v cb = 0 v, ?6 v i c = 1 ma 100 165 80 165 i c = 100 a 90 150 70 150 i c = 10 a 80 120 60 120 current gain matching 2 dh fe i c = 100 a,v cb = 0 v 0.5 3 0.5 6 % offset voltage 3 v os v cb = 0 v, i c = 100 a 40 100 40 200 v offset voltage change ? v os / ? v cb i c = 100 a vs. collector voltage v cb1 = 0 v 11 150 11 200 v v cb2 = ?6 v 11 150 11 200 v offset voltage change ? v os / ? i c v cb = 0 v 12 50 12 75 v vs. collector current i c1 = 10 a, i c2 = 1 ma 12 50 12 75 v bulk resistance r be v cb = 0 v 0.3 0.75 0.3 0.75 ? 10 a i c 1 ma 0.3 0.75 0.3 0.75 ? offset current i os i c = 100 a, v cb = 0 v 6 35 6 45 na collector-base leakage current i cb0 v cb = ?6 v = v max 50 200 50 400 pa noise voltage density 4 e n i c = 1 ma, v cb = 0 f o = 10 hz 0.8 0.8 nv/ hz f o = 100 hz 0.7 0.7 nv/ hz f o = 1 khz 0.7 0.7 nv/ hz f o = 10 khz 0.7 0.7 nv/ hz collector saturation voltage v ce(sat) i c = 1 ma, i b = 100 a 0.025 0.1 0.025 0.1 v C2C rev. c mat03?pecifications electrical characteristics (@ t a = 25 c, unless otherwise noted.) electrical characteristics mat03e mat03f parameter symbol conditions min typ max min typ max unit current gain h fe v cb = 0 v, ?6 v i c = 1 ma 70 120 60 120 i c = 100 a 60 105 50 105 i c = 10 a 5090 4090 offset voltage v os i c = 100 a, v cb = 0 v 30 135 30 265 v offset voltage drift 5 tcv os i c = 100 a, v cb = 0 v 0.3 0.5 0.3 1.0 v/ c offset current i os i c = 100 a, v cb = 0 v 1085 10200 na breakdown voltage bv ceo 36 36 v (@ ?0 c t a 85 c, unless otherwise noted.) notes 1 current gain is measured at collector-base voltages (v cb ) swept from 0 to v max at indicated collector current. typicals are measured at v cb = 0 v. 2 current gain matching ( ? h fe ) is defined as: ? h fe = 100 ( ? i b ) h fe (min ) i c . 3 offset voltage is defined as: v os = v be1 v be2 , where v os is the differential voltage for i c1 = i c2 : v os = v be1 v be2 = kt q in i c 1 i c 2 ? ? ? ? ? ? . 4 sample tested. noise tested and specified as equivalent input voltage for each transistor. 5 guaranteed by v os test (tcv os = v os /t for v os v be ) where t = 2 98 k for t a = 25 c. specifications subject to change without notice.
mat03 C3C rev. c absolute maximum ratings 1 collector-base voltage (bv cbo ) . . . . . . . . . . . . . . . . . . . 36 v collector-emitter voltage (bv ceo ) . . . . . . . . . . . . . . . . . 36 v collector-collector voltage (bv cc ) . . . . . . . . . . . . . . . . . 36 v emitter-emitter voltage (bv ee ) . . . . . . . . . . . . . . . . . . . 36 v collector current (i c ) . . . . . . . . . . . . . . . . . . . . . . . . . . 20 ma emitter current (i e ) . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 ma total power dissipation ambient temperature 70 c 2 . . . . . . . . . . . . . . . 500 mw operating temperature range mat03e/f . . . . . . . . . . . . . . . . . . . . . . . . 40 c to +85 c operating junction temperature . . . . . . . . . 55 c to +150 c storage temperature . . . . . . . . . . . . . . . . . . 65 c to +150 c lead temperature (soldering, 60 sec) . . . . . . . . . . . . . 300 c junction temperature . . . . . . . . . . . . . . . . . 65 c to +150 c notes 1 absolute maximum ratings apply to both dice and packaged devices. 2 rating applies to to-78 not using a heat sink and lcc; devices in free air only. for to-78, derate linearly at 6.3 mw/ c above 70 c ambient temperature; for lcc, derate at 7.8 mw/ c. ordering guide v os max temperature package model (t a = +25 c) range option mat03eh 100 v 40 c to +85 c to-78 mat03fh 200 v 40 c to +85 c to-78 warning! esd sensitive device caution esd (electrostatic discharge) sensitive device. electrostatic charges as high as 4000 v readily accumulate on the human body and test equipment and can discharge without detection. although the mat03 features propriety esd protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. therefore, proper esd precautions are recommended to avoid performance degradation or loss of functionality.
C4C rev. c mat03 tpc 2. current gain vs. temperature tpc 1. current gain vs. collector current tpc 3. gain bandwidth vs. collector current tpc 4. base-emitter voltage vs. collector current tpc 5. small-signal input resistance (h ie ) vs. collector current tpc 6. small signal output con- ductance (h oe ) vs. collector current ?ypical performance characteristics
mat03 C5C rev. c tpc 9. noise voltage density tpc 7. saturation voltage vs. collector current tpc 8. noise voltage density vs. frequency tpc 10. total noise vs. collector current tpc 11. collector-base capacitance vs. v cb
C6C rev. c mat03 figure 1. spice or saber model applications information mat03 models the mat03 model (figure 1) includes parasitic diodes d 3 through d 6 . d 1 and d 2 are internal protection diodes that pre vent zenering of the base-emitter junctions. the analysis programs, spice and saber, are primarily used in evaluating the functional performance of systems. the models are provided only as an aid in using these simulation programs. mat03 noise measurement all resistive components (johnson noise, e n 2 = 4ktbr, or e n = 0.13 r nv/ hz , where r is in k ? ) and semiconductor junctions (shot noise, caused by current flowing through a junction, produces voltage noise in series impedances such as transistor-collector load resistors, i n = 0.566 i pa/ hz where i is in a) contribute to the system input noise. figure 2 illustrates a technique for measuring the equivalent in- put noise voltage of the mat03. 1 ma of stage current is used figure 2. mat03 voltage noise measurement circuit
mat03 C7C rev. c to bias each side of the differential pair. the 5 k ? collector resistors noise contribution is insignificant compared to the volt- age noise of the mat03. since noise in the signal path is referred back to the input, this voltage noise is attenuated by the gain of the circuit. consequently, the noise contribution of the col- lector load resistors is only 0.048 nv/ hz . this is considerably less than the typical 0.8 nv/ hz input noise voltage of the mat03 transistor. the noise contribution of the op27 gain stages is also negli- gible due to the gain in the signal path. the op amp stages amplify the input referred noise of the transistors to increase the signal strength to allow the noise spectral density (e in 10000) to be measured with a spectrum analyzer. since we assume equal noise contributions from each transistor in the mat03, the output is divided by 2 to determine a single transistor s input noise. air currents cause small temperature changes that can appear as low frequency noise. to eliminate this noise source, the mea- surement circuit must be thermally isolated. effects of extraneous noise sources must also be eliminated by totally shielding the circuit. super low noise amplifier the circuit in figure 3a is a super low noise amplifier with equivalent input voltage noise of 0.32 nv/ hz . by paralleling three mat03 matched pairs, a further reduction of amplifier noise is attained by a reduction of the base spreading resistance by a factor of 3, and consequently the noise by 3 . additionally, the shot noise contribution is reduced by maintaining a high collector current (2 ma/device) which reduces the dynamic emitter resistance and decreases voltage noise. the voltage noise is inversely proportional to the square root of the stage current, and current noise increases proportionally to the square root of the stage current. accordingly, this amplifier capitalizes on voltage noise reduction techniques at the expense of increasing the current noise. however, high current noise is not usually important when dealing with low impedance sources. figure 3a. super low noise amplifier
C8C rev. c mat03 this amplifier exhibits excellent full power ac performance, 0.08% thd into a 600 ? load, making it suitable for exacting audio applications (see figure 3b). figure 3b. super low noise amplifiertotal harmonic distortion low noise microphone preamplifier figure 4 shows a microphone preamplifier that consists of a mat03 and a low noise op amp. the input stage operates at a relatively high quiescent current of 2 ma per side, which reduces the mat03 transistor s voltage noise. the 1/ corner is less than 1 hz. total harmonic distortion is under 0.005% for a 10 v p-p signal from 20 hz to 20 khz. the preamp gain is 100, but can be modified by varying r 5 or r 6 (v out /v in = r 5 /r 6 + 1). a total input stage emitter current of 4 ma is provided by q 2 . the constant current in q 2 is set by using the forward voltage of a gaasp led as a reference. the difference between this voltage and the v be of a silicon transistor is predictable and constant (to a few percent) over a wide temperature range. the voltage differ- ence, approximately 1 v, is dropped across the 250 ? resistor which produces a temperature stabilized emitter current. current sources a fundamental requirement for accurate current mirrors and active load stages is matched transistor components. due to the excellent v be matching (the voltage difference between v be s required to equalize collector current) and gain matching, the mat03 can be used to implement a variety of standard current mirrors that can source current into a load such as an amplifier stage. the advantages of current loads in amplifiers versus resistors is an increase of voltage gain due to higher imped- ances, larger signal range, and in many applications a wider signal bandwidth. figure 5 illustrates a cascode current mirror consisting of two mat03 transistor pairs. the cascode current source has a common base transistor in se- ries with the output which causes an increase in output imped- ance of the current source since v ce stays relatively constant. high frequency characteristics are improved due to a reduction of miller capacitance. the small-signal output impedance can be determined by consulting h of vs. collector current typical graph. typical output impedance levels approach the perfor- mance of a perfect current source. considering a typical collector current of 100 a, we have: ro q3 = 1 1. 0 mhos = 1 m ? figure 4. low noise microphone preamplifier
mat03 C9C rev. c q 2 and q 3 are in series and operate at the same current levels so the total output impedance is: r o = h fe ro q3 @ (160)(1 m ? ) = 160 m ? . figure 5. cascode current source current matching the objective of current source or mirror design is generation of currents that are either matched or must maintain a constant ra- tio. however, mismatch of base emitter voltages cause output current errors. consider the example of figure 5. if the resistors and transistors are equal and the collector voltages are the same, the collector currents will match precisely. investigating the cur- rent matching errors resulting from a nonzero v os , we define ? i c as the current error between the two transistors. graph 6b describes the relationship of current matching errors versus offset voltage for a specified average current i c . note that since the relative error between the currents is exponentially proportional to the offset voltage, tight matching is required to design high accuracy current sources. for example, if the offset voltage is 5 mv at 100 a collector current, the current match- ing error would be 20%. additionally, temperature effects such as offset drift (3 v/ c per mv of v os ) will degrade performance if q 1 and q 2 are not well matched. digitally programmable bipolar current pump the circuit of figure 7 is a digitally programmable current pump. the current pump incorporates a dac08, and a fast wilson current source using the mat03. examining figure 7, the dac08 is set for 2 ma full-scale range so that bipolar cur- rent operation of 2 ma is achieved. the wilson current mirror maintains linearity within the lsb range of the 8-bit dac08 ( 2 ma/256 = 15.6 a resolution) as seen in figure 8. a nega- tive feedback path established by q 2 regulates the collector cur- rent so that it matches the reference current programmed by the dac08. collector-emitter voltages across both q 1 and q 3 are matched by d 1 , with q 3 s collector-emitter voltage remaining constant, independent of the voltage across the current source output. since q 2 buffers q 3 , both transistors in the mat03, q 1 and q 3 , maintain the same collector current. d 2 and d 3 form a baker clamp which prevents q 2 from turning off, thereby improving the switching speed of the current mirror. the feedback serves to increase the output impedance and improves accuracy by re- ducing the base-width modulation which occurs with varying collector-emitter voltages. accuracy and linearity performance of the current pump is summarized in figure 8. figure 6a. current matching circuit figure 6b. current matching accuracy % vs. offset voltage figure 7. digitally programmable bipolar current pump
C10C rev. c mat03 figure 8. digitally programmable current pumpinl error as digital code the full-scale output of the dac08, i out , is a linear function of i ref i fr = 256 256 i ref , and i out + i out = i ref 256 256 the current mirror output is i out ? i out = 1, so that if i ref = 2 ma : i = 2 i out 1.992 ma = 2 input code 256 ? ? ? ? ? ? ( 2 ma) 1.992 ma. digital current pump coding digital input b1 . . . b8 output current full range 1111 1111 i = 1.992 ma half range 1000 0000 i = 0.008 ma zero scale 0000 0000 i = 1.992 ma
mat03 C11C rev. c outline dimensions dimensions shown in inches and (mm). to-78 metal can 0.250 (6.35) min 0.750 (19.05) 0.500 (12.70) 0.185 (4.70) 0.165 (4.19) reference plane 0.050 (1.27) max 0.019 (0.48) 0.016 (0.41) 0.021 (0.53) 0.016 (0.41) 0.045 (1.14) 0.010 (0.25) 0.040 (1.02) max base & seating plane 0.335 (8.51) 0.305 (7.75) 0.370 (9.40) 0.335 (8.51) 0.034 (0.86) 0.027 (0.69) 0.045 (1.14) 0.027 (0.69) 0.160 (4.06) 0.110 (2.79) 0.100 (2.54) bsc 5 2 6 4 3 1 0.200 (5.08) bsc 0.100 (2.54) bsc 45 bsc revision history location page data sheet changed from rev. b to rev. c. edits to electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 deleted wafer test limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 deleted dice characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 edits to ordering guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 edits to absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
C12C c00284-0-2/02(c) printed in u.s.a.

▲Up To Search▲

Price & Availability of MAT03AH883C

	To Download MAT03AH883C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .